Lỗi máy in HP M102

Lỗi máy in HP M101/M102/M103 - HP LaserJet M103 Pro Error Codes 


  • Error Code 01 HP M101/M102/M103 
  • Display:The Ready and Attention lights are on.
  • Description:The printer has experienced a fatal error.
  • Causes:The printer has experienced a fatal error.
  • Remedy:Check for secondary control-panel light patterns

1. Press and hold down the Resume/Cancel button.

2. If the state of the lights changes (for example, if the LEDs start blinking) a fatal error is indicated. Go to Secondary controlpanel light patterns to find the fatal error description.
NOTE: If the state of the lights does not change, there is no secondary LED state.

  • Code 02 HP M101/M102/M103 
  • Display:The Ready light is off and the Attention light is on.
  • Description:Engine error
  • Causes:

• Communication error

• DCC memory error 

• Unknown engine firmware error

  • Remedy:

1. Turn the printer off, and then on.

2. If the error persists, reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize.

3. If a surge protector is used: a. Turn the printer off. b. Remove the surge protector. c. Plug the printer directly into the wall socket and turn the printer on.

4. If the error persists, the printer will require service.

error-code-hp-m101-m102

Error code hp m101/m102/m103

Error code HP LaserJet M101 Pro, HP LaserJet M102 Pro, HP LaserJet M103 Pro

  • Code 03 HP M101/M102/M103 
  • Display:The Ready light is blinking and the Attention light is on.
  • Description:Power error
  • Causes:

• Low-voltage power supply (LVPS)

• Power outage detected

  • Remedy:

1. Recovering from power failure. Please wait.

2. If the error persists, reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize.

3. If a surge protector is used: a. Turn the printer off. b. Remove the surge protector. c. Plug the printer directly into the wall socket and turn the printer on.

4. If the error persists, the printer will require service.

 
  • Error Code 04 HP M101/M102/M103 
  • Display:The Ready light is on and the Attention light is blinking.
  • Description:Fuser error
  • Causes:

• Bad fuser

• Low fuser

• Slow fuser

• High fuser

• Fuser drive

• Fuser release lever

• Low fuser temp 2 

• High fuser temp 2 

• Low fuser temp 3 

• High fuser temp 3

  • Remedy:

1. Check the power source. Make sure the power source meets printer requirements.

2. Turn the printer off, and then on.

3. If the error persists, reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize.

4. If a surge protector is used: a. Turn the printer off. b. Remove the surge protector. c. Plug the printer directly into the wall socket and turn the printer on.

5. If the error persists, the printer will require service.

  • Error Code 05 HP M101/M102/M103 
  • Display:The Ready and Attention lights are blinking.
  • Description:General engine error
  • Causes:General engine error
  • Remedy:

1. Turn the printer off, and then on.

2. If the error persists, reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize.

3. If a surge protector is used: a. Turn the printer off. b. Remove the surge protector. c. Plug the printer directly into the wall socket and turn the printer on.

4. If the error persists, the printer will require service.

loi-hp-m102

Error 05-06-07 Printer hp M101/m102/m103

Error code HP LaserJet M101 Pro, HP LaserJet M102 Pro, HP LaserJet M103 Pro

  • Error Code 06 HP M101/M102/M103 
  • Display:The Ready and Attention lights are cycling on and off.
  • Description:Sensor error
  • Causes:• Sensor dirty • Level sensor error • Bad TOP sensor
  • Remedy:1. Turn the printer off, and then on. 2. If the error persists, reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize. 3. If a surge protector is used: a. Turn the printer off. b. Remove the surge protector. c. Plug the printer directly into the wall socket and turn the printer on. 4. If the error persists, the printer will require service.
  • Error Code 07 HP M101/M102/M103 
  • Display:The Ready light is blinking and the Attention light is off.
  • Description:Motor rotation error
  • Causes:

• Bad fuser motor start

• Bad fuser motor

• Bad drum motor start 

• Bad drum motor rotation

• Bad developer motor start 

• Bad developer motor rotation

• Bad main motor start 

• T2 clutch error 

• Bad main motor

• Bad developer motor 

• T1 alienation

  • Remedy:

1. Turn the printer off, and then on.

2. If the error persists, reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize.

3. If a surge protector is used:

a. Turn the printer off.

b. Remove the surge protector.

c. Plug the printer directly into the wall socket and turn the printer on.

4. If the error persists, the printer will require service.

Error code HP LaserJet M101 Pro, HP LaserJet M102 Pro, HP LaserJet M103 Pro
  • Error Code 08 HP M101/M102/M103 

  • Display:The Ready and Attention lights are off.

  • Description:Laser failure

  • Causes:Laser failure

  • Remedy:

1. Turn the printer off, and then on.

2. If the error persists, reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize.

3. If a surge protector is used:

a. Turn the printer off.

b. Remove the surge protector.

c. Plug the printer directly into the wall socket and turn the printer on.

4. If the error persists, the printer will require service.

may-in-hp-107-tai-hai-duong

Lỗi máy in HP

Bản dịch google

Mã lỗi máy in HP M101/M102/M103 | Bảo Tín 0983593218

  • Lỗi 01 máy in HP M101/M102/M103 

  • Trưng bày:Đèn Sẵn sàng và Chú ý đang bật.

  • Sự miêu tả:Máy in đã gặp lỗi nghiêm trọng.

  • Nguyên nhân:Máy in đã gặp lỗi nghiêm trọng.

  • Biện pháp khắc phục:

Kiểm tra các kiểu đèn của bảng điều khiển phụ

1. Nhấn và giữ nút Tiếp tục / Hủy. 

2. Nếu trạng thái của đèn thay đổi (ví dụ: nếu đèn LED bắt đầu nhấp nháy), một lỗi nghiêm trọng sẽ được chỉ ra. Đi tới Mẫu đèn bảng điều khiển phụ để tìm mô tả lỗi nghiêm trọng.
LƯU Ý: Nếu trạng thái của đèn không thay đổi thì không có trạng thái đèn LED thứ cấp.

  • Lỗi 02 máy in HP M101/M102/M103 
  • Trưng bày:Đèn Sẵn sàng tắt và đèn Chú ý sáng.
  • Sự miêu tả:Lỗi kĩ thuật
  • Nguyên nhân:

• Lỗi giao tiếp

• Lỗi bộ nhớ DCC

• Lỗi phần sụn động cơ không xác định

  • Biện pháp khắc phục:

1. Tắt máy in rồi bật lại. 

2. Nếu lỗi vẫn còn, hãy đặt lại máy in:

a. Tắt nguồn bằng cách sử dụng công tắc nguồn, sau đó đợi ít nhất 30 giây. 

b. Bật nguồn và đợi sản phẩm khởi chạy. 

3. Nếu sử dụng thiết bị chống sét lan truyền:

a. Tắt máy in. 

b. Tháo bộ chống sét lan truyền. 

c. Cắm trực tiếp máy in vào ổ cắm trên tường và bật máy in.

 4. Nếu lỗi vẫn còn, máy in sẽ yêu cầu bảo dưỡng.

  • Lỗi 03 máy in HP M101/M102/M103 
  • Trưng bày:Đèn Sẵn sàng nhấp nháy và đèn Chú ý sáng.
  • Sự miêu tả:Lỗi nguồn
  • Nguyên nhân:

• Nguồn điện áp thấp (LVPS)

• Đã phát hiện tình trạng mất điện

  • Biện pháp khắc phục:

1. Phục hồi sau khi mất điện. Vui lòng chờ. 

2. Nếu lỗi vẫn còn, hãy đặt lại máy in: a. Tắt nguồn bằng cách sử dụng công tắc nguồn, sau đó đợi ít nhất 30 giây. b. Bật nguồn và đợi sản phẩm khởi chạy. 

3. Nếu sử dụng thiết bị chống sét lan truyền:

a. Tắt máy in. 

b. Tháo bộ chống sét lan truyền. 

c. Cắm trực tiếp máy in vào ổ cắm trên tường và bật máy in. 

4. Nếu lỗi vẫn còn, máy in sẽ yêu cầu bảo dưỡng.

canh-bao-loi-may-in
lỗi máy in hp m101/m102/m103 
  • Lỗi 04 máy in HP M101/M102/M103 

  • Trưng bày:Đèn Sẵn sàng sáng và đèn Chú ý nhấp nháy.
  • Sự miêu tả:Fuser error
  • Nguyên nhân:

• Bộ nhiệt áp kém

• Bộ nhiệt áp thấp

• Bộ nhiệt áp chậm

• Bộ nhiệt áp cao • Ổ đĩa nhiệt độ

• Cần nhả bộ nhiệt áp

• Nhiệt độ bộ nhiệt áp thấp 2

• Nhiệt độ bộ nhiệt áp cao 2

• Nhiệt độ bộ nhiệt áp thấp 3

• Nhiệt độ bộ nhiệt áp cao 3

  • Biện pháp khắc phục:

1. Kiểm tra nguồn điện. Đảm bảo nguồn điện đáp ứng các yêu cầu của máy in. 

2. Tắt máy in rồi bật lại.

 3. Nếu lỗi vẫn còn, hãy đặt lại máy in: a. Tắt nguồn bằng cách sử dụng công tắc nguồn, sau đó đợi ít nhất 30 giây. b. Bật nguồn và đợi sản phẩm khởi chạy. 

4. Nếu sử dụng thiết bị chống sét lan truyền:

a. Tắt máy in. 

b. Tháo bộ chống sét lan truyền. 

c. Cắm trực tiếp máy in vào ổ cắm trên tường và bật máy in.

5. Nếu lỗi vẫn còn, máy in sẽ yêu cầu bảo dưỡng.

  • Lỗi 05 máy in HP M101/M102/M103 
  • Trưng bày:Các đèn Sẵn sàng và Chú ý đang nhấp nháy.
  • Sự miêu tả:Lỗi động cơ chung
  • Nguyên nhân:Lỗi động cơ chung
  • Biện pháp khắc phục:

1. Tắt máy in rồi bật lại. 

2. Nếu lỗi vẫn còn, hãy đặt lại máy in:

a. Tắt nguồn bằng cách sử dụng công tắc nguồn, sau đó đợi ít nhất 30 giây.

 b. Bật nguồn và đợi sản phẩm khởi chạy. 

3. Nếu sử dụng thiết bị chống sét lan truyền:

a. Tắt máy in. 

b. Tháo bộ chống sét lan truyền. 

c. Cắm trực tiếp máy in vào ổ cắm trên tường và bật máy in.

4. Nếu lỗi vẫn còn, máy in sẽ yêu cầu bảo dưỡng.

sua-may-in-hai-duong

lỗi máy in hp

  • Lỗi 06 máy in HP M101/M102/M103 

  • Trưng bày:Các đèn Sẵn sàng và Chú ý đang bật và tắt.
  • Sự miêu tả:Lỗi cảm biến
  • Nguyên nhân:

• Cảm biến bị bẩn

• Lỗi cảm biến mức

• Cảm biến TOP kém

  • Biện pháp khắc phục:

1. Tắt máy in rồi bật lại. 

2. Nếu lỗi vẫn còn, hãy đặt lại máy in:

a. Tắt nguồn bằng cách sử dụng công tắc nguồn, sau đó đợi ít nhất 30 giây. 

b. Bật nguồn và đợi sản phẩm khởi chạy. 

3. Nếu sử dụng thiết bị chống sét lan truyền:

a. Tắt máy in.

b. Tháo bộ chống sét lan truyền. 

c. Cắm trực tiếp máy in vào ổ cắm trên tường và bật máy in. 

4. Nếu lỗi vẫn còn, máy in sẽ yêu cầu bảo dưỡng.

  • Lỗi 07 máy in HP M101/M102/M103 
  • Trưng bày:Đèn Sẵn sàng nhấp nháy và đèn Chú ý tắt.
  • Sự miêu tả:Lỗi quay động cơ
  • Nguyên nhân:

• Khởi động động cơ bộ sấy kém

• Động cơ bộ sấy kém • Khởi động động cơ trống không tốt

• Vòng quay động cơ trống không tốt

• Khởi động động cơ của nhà phát triển kém • Vòng quay của động cơ của nhà phát triển không tốt

• Khởi động động cơ chính không tốt

• Lỗi ly hợp T2

• Động cơ chính bị lỗi

• Động cơ của nhà phát triển kém

• Lỗi T1

  • Biện pháp khắc phục:

1. Tắt máy in rồi bật lại.

 2. Nếu lỗi vẫn còn, hãy đặt lại máy in:

a. Tắt nguồn bằng cách sử dụng công tắc nguồn, sau đó đợi ít nhất 30 giây. 

b. Bật nguồn và đợi sản phẩm khởi chạy. 

3. Nếu sử dụng thiết bị chống sét lan truyền:

a. Tắt máy in. 

b. Tháo bộ chống sét lan truyền. 

c. Cắm trực tiếp máy in vào ổ cắm trên tường và bật máy in. 

4. Nếu lỗi vẫn còn, máy in sẽ yêu cầu bảo dưỡng.

  • Lỗi 08 máy in HP M101/M102/M103 
  • Trưng bày:Đèn Sẵn sàng và Chú ý tắt.
  • Sự miêu tả:Lỗi laser
  • Nguyên nhân:Lỗi laser
  • Biện pháp khắc phục:

1. Tắt máy in rồi bật lại. 

2. Nếu lỗi vẫn còn, hãy đặt lại máy in:

a. Tắt nguồn bằng cách sử dụng công tắc nguồn, sau đó đợi ít nhất 30 giây. 

b. Bật nguồn và đợi sản phẩm khởi chạy. 

3. Nếu sử dụng thiết bị chống sét lan truyền:

a. Tắt máy in. 

b. Tháo bộ chống sét lan truyền. 

c. Cắm trực tiếp máy in vào ổ cắm trên tường và bật máy in. 

4. Nếu lỗi vẫn còn, máy in sẽ yêu cầu bảo dưỡng.

chuyen-sua-may-in-hai-duong

sửa máy in Hải Dương 0983593218



Link tham gia nhóm reset máy in HP - chia sẻ kỹ thuật máy in ---->> tại đây 

Tham gia nhóm hỗ trợ kỹ thuật

 

Đổ mực máy in - Sửa máy in - Máy khoan pinMáy in cũ - Vật tư máy in - Reset máy in HP

*******************************************************************************

Nhóm hỗ trợ kỹ thuật - reset máy in: tại đây

*******************************************************************************


TRUNG TÂM DỊCH VỤ KỸ THUẬT BẢO TÍN

Địa chỉ: Số 240 Nguyễn Văn Linh - Tp. Hải Dương.

Điện thoại: 0220. 3891 366 -  Mobile: 0983 593 218 (zalo/facebook)

Website: http://suamayinhaiduong.net/ 

Tags: may in hai duongsua may in hai duongdo muc in hai duongmay in cu hai duongsua may chieu hai duong, may chieu hai duongsua may in uy tin hai duong,sua may in chuyen nghiep hai duong, sua may photo hai duong, sua may in hai duong, do muc in chat luong cao hai duong, do muc may in hai duong, do muc may in tai hai duong, do muc in hai duong

 

Tìm Sản Phẩm
Đăng ký | Đăng nhập

Email / Điện thoại

Mật khẩu

Nhớ mật khẩu | Quên mật khẩu

Nhận tin mới
Bạn biết đến dịch vụ chúng tôi thông qua
Bạn bè
Tìm kiếm trên internet
Quen biết
Khác

Thống kê truy cập
Đang truy cập: 8
Trong ngày: 20
Trong tuần: 791
Lượt truy cập: 2459559
  hp1010máy in hải dương máy in sửa máy in đổ mực inmáy in cũ máy in Hải Dương máy in đảo mặt máy in cũ máy in canon3300 máy in canon6300 máy in hp401d Hải Dươnghp2055d máy inhp2055d máy in hải dương bán máy in hộp mực 2055d đổ mực 2055d đổ mực in hải dươngmáy in canon canon 6300dn máy in 6300dn máy in cũ hải dương máy in canon hộp mực 6300dnmáy in cũ canon canon3018 máy in hải dương máy in cũ máy in canon3108trục từ trục từ canon trục từ hp trục từ máy inbochiamayinbộ chia 4 cổng bộ chia máy in 4 cổng bộ chia máy inmáy in hpm135w hpm135w Hải Dương máy in đa năng sửa chữaneverstop hp mucinhp1000w mucdoneverstopđiều khển máy chiếu điều khiển đa năng máy chiếu khien da nang dieu khien may chieu hai duongmực đổ hp1000w mực đổ hp neverstop mực đổ hải dương đổ mực hpcanon6670 mayincanon máy in canon hải dương đổ mực canonreset samsung reset máy in reset máy in samsung. samsungcanon đa năng canon D520 Hp1212nfxerox p225 máy in cũ p225 xerox p225Canon 6200d máy in canon máy in cũ canon 6200d tại Hải Dươngmực đổ hp107 mực hp hải dươngmáy in hp403dw máy in hải dương hp403dw hp m403dwHộp mực máy 3300 hộp mực hải dương canon 3300 hải dươngHộp mực canon 6200 canon 6200 hộp mực incanon 6200máy in canon máy in canon 3310chíp mực hpm348 chíp mực hpm436 chip hpm436 hpm438chip drum hp436 chíp trống hp436 chip drum hp438máy in cũ hải dương máy a3 hải dương hp706kitreset kithafrimwa ha version hpmáy in mayin in bill máy in wificard in canon 2900 canon 2900 card wifi 2900canon2900 canon2900w 2900w mayincanon 2900sửa máy inmáy in tại Hải Dươngsửa máy in 2900đổ mực in 2900Hải Dươngđổ mực in Hải Dươnglỗi máy in hpm436hp m436error C3-14141máy in hphải dươnglỗi c3-14141 hp436

rivew-maps

TRUNG TÂM DỊCH VỤ KỸ THUẬT BẢO TÍN ĐC: Số 240 Nguyễn Văn Linh - Tp. Hải Dương. Mobile: 0983 593 218 (zalo/facebook)
1
Bạn cần hỗ trợ?