Lỗi máy in Brother HL2321 - ERROR CODE BROTHER HL2321

Lỗi 4D01 máy in Brother HL2321

Error Code 4D01 Brother HL2321

• Display:Replace Toner
• Description:Dot count or develop roller counter of the toner has reached the upper limit in the toner continuous printing mode.
• Remedy: • Replace the toner cartridge which has reached the upper limit.
  1 If the error display is not cleared after replacing the toner cartridge with a new one, the main PCB is faulty. Replace the main PCB ASSY.

Lỗi 4E01 máy in Brother HL2321

Error Code 4E01 Brother HL2321

• Display:Toner Ended Open the Front Cover, replace Toner Cartridge.
• Description:The toner cartridge has reached the upper limit in the toner continuous printing mode.
• Remedy: • Replace the toner cartridge which has reached the upper limit.
  1 If the error display is not cleared after replacing the toner cartridge with a new one, the main PCB is faulty. Replace the main PCB ASSY.

Lỗi 4F01 máy in Brother HL2321

Error Code 4F01 Brother HL2321

• Display:Cartridge Error Put the Toner Cartridge back in.
• Description:The new toner sensor could not detect the new toner cartridge correctly.
• Remedy: • Replace the toner cartridge with a new one again. • If the machine is on the uneven surface, place it on a level surface.
  1 Connection failure of the new toner sensor PCB flat cable Reconnect the new toner sensor PCB flat cable. 2 New toner actuator coming off or caught in sections of the machine Reattach the new toner actuator. 3 Develop joint coming off or caught in sections of the machine Reattach the develop joint. 4 New toner sensor failure Replace the new toner sensor PCB ASSY. 5 Panel PCB failure Replace the panel PCB ASSY. 6 If the error display is not cleared after replacing the toner cartridge with a new one, the main PCB is faulty. Replace the main PCB ASSY.

Lỗi 6001 máy in Brother HL2321

Error Code 6001 Brother HL2321

• Display:Cover is Open Close the Front Cover.
• Description:The front cover sensor detected that the front cover was open.
• Remedy: • Close the front cover.
  1 Front cover failure Replace the front cover. 2 Front cover sensor failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Lỗi 6004 máy in Brother HL2321

Error Code 6004 Brother HL2321

• Display:Cover is Open Close the Fuser Cover which can be found behind the Back Cover of the machine.
• Description:The eject sensor detected the open fuser cover was open.
• Remedy: • Close the fuser cover.
  1 Eject actuator coming off or caught in sections of the machine Reattach the eject actuator. 2 Fuser cover attachment failure Reattach the fuser cover. 3 Connection failure of the eject sensor PCB flat cable Reconnect the eject sensor PCB flat cable. 4 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

Lỗi 6101 máy in Brother HL2321

Error Code 6101 Brother HL2321

• Display:No Toner Open the Front Cover, then install Toner Cartridge.
• Description:The new toner sensor detected that the toner cartridge was not set.
• Remedy: • Set the toner cartridge correctly. • Replace the toner cartridge with a new one.
  1 New toner actuator coming off Reattach the new toner actuator. 2 Connection failure of the new toner sensor PCB flat cable Reconnect the new toner sensor PCB flat cable. 3 Connection failure of the panel PCB flat cable Reconnect the panel PCB flat cable. 4 New toner sensor PCB failure Replace the new toner sensor PCB ASSY. 5 Panel PCB failure Replace the panel PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

Lỗi 6801 máy in Brother HL2321

Error Code 6801 Brother HL2321

• Display:Cooling Down Wait for a while
• Description:The side thermistor of the fuser unit detected a temperature higher than the specified value.
• Remedy: • Lower the room temperature. • Keep the machine away from heating appliances.
  1 Side thermistor failure Replace the fuser unit. 2 Main PCB failure Replace the main PCB ASSY.

Lỗi 6901 máy in Brother HL2321

Code 6901 Brother HL2321

• Display:Self-Diagnostic Turn the power off, then on again. Leave the machine for 15 min.
• Description:An error occurred in the fuser unit when the power switch was turned ON or sleep mode was released.
• Remedy:1 Connection failure of each fuser unit harness Reconnect each harness of the fuser unit. 2 Connection failure of the eject sensor PCB flat cable Reconnect the eject sensor PCB flat cable. 3 Fuser unit failure Replace the fuser unit. 4 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.
  Note: • Turn OFF the power switch. After the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for 15 minutes. This problem may then be cleared. • To release the fuser unit error after taking appropriate measures, enter the maintenance mode once and quit it with the maintenance code 99.

Lỗi 6902 máy in Brother HL2321

Error Code 6902 Brother HL2321

• Display:Self-Diagnostic Will Automatically Restart within 15 minutes.
• Description:Rechecking the error after the power switch was turned OFF and then ON again because an error was detected in the fuser unit. (This message is displayed for approximately 15 minutes when the machine is restarted after error code 6901 has occurred.)
• Remedy:1 Connection failure of each fuser unit harness Reconnect each harness of the fuser unit. 2 Connection failure of the eject sensor PCB flat cable Reconnect the eject sensor PCB flat cable. 3 Fuser unit failure Replace the fuser unit. 4 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.
  Note: • Turn OFF the power switch. After the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for 15 minutes. This problem may then be cleared. • To release the fuser unit error after taking appropriate measures, enter the maintenance mode once and quit it with the maintenance code 99.

Sửa chữa máy in tại Hải Dương

TRUNG TÂM DỊCH VỤ KỸ THUẬT BẢO TÍN

 “MUA BÁN - BẢO HÀNH - SỬA CHỮA MÁY KHOAN BẮT VÍT CHẠY PIN TẠI HẢI DƯƠNG”

*****

Địa chỉ: Số 240 Nguyễn Văn Linh - Tp. Hải Dương.

Điện thoại: 0220. 3891 366 -  Mobile: 0983 593 218 (zalo/facebook)

Website: http://suamayinhaiduong.net/ 

---->>>>>fb/luongthanhthiep <<<----

---->>>Tiktok<<<-----

Tags: may in hai duong, sua may in hai duong, do muc in hai duong, may in cu hai duong, sua may chieu hai duong, may chieu hai duong, sua may in uy tin hai duong,sua may in chuyen nghiep hai duong, sua may photo hai duong, sua may in hai duong, do muc in chat luong cao hai duong, do muc may in hai duong, do muc may in tai hai duong, do muc in hai duong

Đổ mực máy in - Sửa máy in - Máy khoan pin - Dịch vụ sửa chữa máy in - Máy in cũ