Lỗi máy in Brother HL2321D - ERROR CODE BROTHER HL2321

Lỗi 6A00 máy in Brother HL2321

Error Code 6A00 Brother HL2321

• Display:Drum ! Slide the Green tab on Drum Unit.
• Description:Detected discharge that may be attributable to dirty corona wire on the drum unit.
• Remedy:<User Check> • Slide the green tab of the drum unit to left and right for two to three times to clean the corona wire. • Clean the terminal of the drum unit. • Replace the drum unit.
  1 Dirt on the high-voltage power supply PCB terminal Clean the electrodes of the machine. 2 High voltage electrodes attachment failure Check if the problem disappears after pressing each electrode. If not, reattach the electrodes. 3 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

Lỗi 6F00 máy in Brother HL2321

Error Code 6F00 Brother HL2321

• Display:Print Unable ZC Turn the power off and then back on again.
• Description:Detected irregular power supply for less than 100 times.
• Remedy:<User Check> • Turn the power switch OFF and then back ON again. • Put a filter into the power supply. • Install a voltage stabilizer to the power supply unit.

Lỗi máy in Brother HL2321

Error Code 7000 Brother HL2321

• Display:Jam Inside Open the Front Cover, pull out the Drum Unit completely and remove the jammed paper.
• Description:The eject sensor does not detect paper pass after the registration rear sensor detected the paper pass.
• Remedy:<User Check> • Remove the jammed paper.
  1 Foreign object inside the machine Remove the foreign object. 2 Connection failure of the eject sensor PCB flat cable Reconnect the eject sensor PCB flat cable. 3 Eject actuator coming off or caught in sections of the machine Reattach the eject actuator. 4 Fuser cover attachment failure Reattach the fuser cover. 5 Eject sensor failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Damaged gears in the feeding system Replace the main frame L ASSY. 8 Main PCB failure Replace the main PCB ASSY.

Lỗi 7100 máy in Brother HL2321

Error Code 7100 Brother HL2321

• Display:Jam Rear Open the Back Cover and remove the jammed paper, then press Go.
• Description:The eject sensor remains ON (paper pass detected) even after the registration rear sensor detected the end of paper pass.
• Remedy:<User Check> • Remove the jammed paper. • Check if the back cover is open during duplex printing.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 Eject actuator caught in sections of the machine Reattach the eject actuator. 3 Fuser cover attachment failure Reattach the fuser cover. 4 Eject sensor failure Replace the eject sensor PCB ASSY. 5 Fuser unit failure Replace the fuser unit. 6 Damaged gears in the feeding system Replace the main frame L ASSY. 7 Main PCB failure Replace the main PCB ASSY.

Lỗi 7300 máy in Brother HL2321

Error Code 7300 Brother HL2321

• Display:Jam Tray 1 Remove the jammed paper from Tray 1.
• Description:When printing from the paper tray, the registration front sensor does not detect paper pass within the specified time after the paper feed sensor detected paper pass.
• Remedy:<User Check> • Remove the jammed paper. • Close the paper tray correctly.
  1 Foreign object in the front section of the paper tray Remove the foreign object. 2 Paper dust cleaning roller attachment failure Reattach the paper dust cleaning roller. 3 Connection failure of the registration front/rear sensor PCB harness Reconnect the registration front/rear sensor PCB harness. 4 Connection failure of the HVPS flat cable Reconnect the HVPS flat cable. 5 Registration front actuator coming off or caught in some sections of the machine Reattach the registration front actuator. 6 HVPS flat cable breakage Replace the HVPS flat cable. 7 Registration front sensor failure Replace the registration front/rear actuator holder ASSY. 8 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 9 Damaged gears in the feeding system Replace the main frame L ASSY. 10 Main PCB failure Replace the main PCB ASSY.

Lỗi 7700 máy in Brother HL2321

Error Code 7700 Brother HL2321

• Display:Jam 2-sided Pull out the Duplex Tray at the back of the machine and remove the jammed paper.
• Description:The registration front sensor does not detect paper pass within the specified time after the first side was printed in duplex printing mode.
• Remedy:<User Check> • Remove the jammed paper. • Close the back cover correctly. • Close the paper tray correctly.
  1 Foreign object in the duplex paper feed system Remove the foreign object. 2 Foreign object in the duplex paper feed system of the paper tray Remove the foreign object. 3 Back cover attachment failure Reattach the back cover. 4 Fuser cover attachment failure Reattach the fuser cover. 5 Duplex tray failure Replace the duplex tray. 6 Damaged gears in the feeding system Replace the main frame L ASSY. 7 Main PCB failure Replace the main PCB ASSY.

Lỗi 7C00 máy in Brother HL2321

Error Code 7C00 Brother HL2321

• Display:Cover is Open Make sure there is no paper jammed inside the machine and close the Back Cover, then press Go.
• Description:The eject sensor was ON when the power switch was turned ON.
• Remedy:<User Check> • Close the back cover correctly.
  1 Eject actuator caught in sections of the machine Reattach the eject actuator. 2 Fuser cover attachment failure Reattach the fuser cover. 3 Back cover attachment failure Reattach the back cover. 4 Eject sensor failure Replace the eject sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.
  

Lỗi 8000 máy in Brother HL2321

Error Code 8000 Brother HL2321

• Display:Print Overrun
• Description:First side printing started before receiving the second side data in duplex printing mode due to the insufficient memory.
• Remedy:<User Check> • Print the print data stored in the memory. • The size of printing data per page is too big. Change the printing contents to reduce the data size. • Switch to single-side printing.
  1 Main PCB failure Replace the main PCB ASSY.

Lỗi 8903 máy in Brother HL2321

Error Code 8903 Brother HL2321

• Display:2-sided Disabled Close the Back Cover of the machine.
• Description:The back cover sensor detected that the cover was open in duplex printing mode. (Before registering printing data to engine)
• Remedy:<User Check> • Close the back cover correctly.
  1 Back cover/duplex tray empty sensor attachment failure Reattach the back cover/duplex tray empty sensor. 2 Boss to push the back cover sensor is broken. Replace the back cover. 3 Back cover/duplex tray empty sensor failure Replace the eject sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

Chuyên sửa máy in tại Hải Dương

TRUNG TÂM DỊCH VỤ KỸ THUẬT BẢO TÍN

 “MUA BÁN - BẢO HÀNH - SỬA CHỮA MÁY KHOAN BẮT VÍT CHẠY PIN TẠI HẢI DƯƠNG”

*****

Địa chỉ: Số 240 Nguyễn Văn Linh - Tp. Hải Dương.

Điện thoại: 0220. 3891 366 -  Mobile: 0983 593 218 (zalo/facebook)

Website: http://suamayinhaiduong.net/ 

---->>>>>fb/luongthanhthiep <<<----

---->>>Tiktok<<<-----

Tags: may in hai duong, sua may in hai duong, do muc in hai duong, may in cu hai duong, sua may chieu hai duong, may chieu hai duong, sua may in uy tin hai duong,sua may in chuyen nghiep hai duong, sua may photo hai duong, sua may in hai duong, do muc in chat luong cao hai duong, do muc may in hai duong, do muc may in tai hai duong, do muc in hai duong

Đổ mực máy in - Sửa máy in - Máy khoan pin - Dịch vụ sửa chữa máy in - Máy in cũ