Sửa máy in | Đổ mực máy in tại Hải Dương

Lỗi máy in Brother HL2321D - ERROR CODE BROTHER HL2321

Lỗi 6A00 máy in Brother HL2321

Error Code 6A00 Brother HL2321

Display:Drum ! Slide the Green tab on Drum Unit.
Description:Detected discharge that may be attributable to dirty corona wire on the drum unit.
Remedy:<User Check> • Slide the green tab of the drum unit to left and right for two to three times to clean the corona wire. • Clean the terminal of the drum unit. • Replace the drum unit.
1 Dirt on the high-voltage power supply PCB terminal Clean the electrodes of the machine. 2 High voltage electrodes attachment failure Check if the problem disappears after pressing each electrode. If not, reattach the electrodes. 3 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

Lỗi 6F00 máy in Brother HL2321

Error Code 6F00 Brother HL2321

Display:Print Unable ZC Turn the power off and then back on again.
Description:Detected irregular power supply for less than 100 times.
Remedy:<User Check> • Turn the power switch OFF and then back ON again. • Put a filter into the power supply. • Install a voltage stabilizer to the power supply unit.

Lỗi máy in Brother HL2321

Error Code 7000 Brother HL2321

Display:Jam Inside Open the Front Cover, pull out the Drum Unit completely and remove the jammed paper.
Description:The eject sensor does not detect paper pass after the registration rear sensor detected the paper pass.
Remedy:<User Check> • Remove the jammed paper.
1 Foreign object inside the machine Remove the foreign object. 2 Connection failure of the eject sensor PCB flat cable Reconnect the eject sensor PCB flat cable. 3 Eject actuator coming off or caught in sections of the machine Reattach the eject actuator. 4 Fuser cover attachment failure Reattach the fuser cover. 5 Eject sensor failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Damaged gears in the feeding system Replace the main frame L ASSY. 8 Main PCB failure Replace the main PCB ASSY.

Lỗi 7100 máy in Brother HL2321

Error Code 7100 Brother HL2321

Display:Jam Rear Open the Back Cover and remove the jammed paper, then press Go.
Description:The eject sensor remains ON (paper pass detected) even after the registration rear sensor detected the end of paper pass.
Remedy:<User Check> • Remove the jammed paper. • Check if the back cover is open during duplex printing.
1 Foreign object in the rear of the machine Remove the foreign object. 2 Eject actuator caught in sections of the machine Reattach the eject actuator. 3 Fuser cover attachment failure Reattach the fuser cover. 4 Eject sensor failure Replace the eject sensor PCB ASSY. 5 Fuser unit failure Replace the fuser unit. 6 Damaged gears in the feeding system Replace the main frame L ASSY. 7 Main PCB failure Replace the main PCB ASSY.

Lỗi 7300 máy in Brother HL2321

Error Code 7300 Brother HL2321

Display:Jam Tray 1 Remove the jammed paper from Tray 1.
Description:When printing from the paper tray, the registration front sensor does not detect paper pass within the specified time after the paper feed sensor detected paper pass.
Remedy:<User Check> • Remove the jammed paper. • Close the paper tray correctly.
1 Foreign object in the front section of the paper tray Remove the foreign object. 2 Paper dust cleaning roller attachment failure Reattach the paper dust cleaning roller. 3 Connection failure of the registration front/rear sensor PCB harness Reconnect the registration front/rear sensor PCB harness. 4 Connection failure of the HVPS flat cable Reconnect the HVPS flat cable. 5 Registration front actuator coming off or caught in some sections of the machine Reattach the registration front actuator. 6 HVPS flat cable breakage Replace the HVPS flat cable. 7 Registration front sensor failure Replace the registration front/rear actuator holder ASSY. 8 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 9 Damaged gears in the feeding system Replace the main frame L ASSY. 10 Main PCB failure Replace the main PCB ASSY.

Lỗi 7700 máy in Brother HL2321

Error Code 7700 Brother HL2321

Display:Jam 2-sided Pull out the Duplex Tray at the back of the machine and remove the jammed paper.
Description:The registration front sensor does not detect paper pass within the specified time after the first side was printed in duplex printing mode.
Remedy:<User Check> • Remove the jammed paper. • Close the back cover correctly. • Close the paper tray correctly.
1 Foreign object in the duplex paper feed system Remove the foreign object. 2 Foreign object in the duplex paper feed system of the paper tray Remove the foreign object. 3 Back cover attachment failure Reattach the back cover. 4 Fuser cover attachment failure Reattach the fuser cover. 5 Duplex tray failure Replace the duplex tray. 6 Damaged gears in the feeding system Replace the main frame L ASSY. 7 Main PCB failure Replace the main PCB ASSY.

Lỗi 7C00 máy in Brother HL2321

Error Code 7C00 Brother HL2321

Display:Cover is Open Make sure there is no paper jammed inside the machine and close the Back Cover, then press Go.
Description:The eject sensor was ON when the power switch was turned ON.
Remedy:<User Check> • Close the back cover correctly.
1 Eject actuator caught in sections of the machine Reattach the eject actuator. 2 Fuser cover attachment failure Reattach the fuser cover. 3 Back cover attachment failure Reattach the back cover. 4 Eject sensor failure Replace the eject sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

Lỗi 8000 máy in Brother HL2321

Error Code 8000 Brother HL2321

Display:Print Overrun
Description:First side printing started before receiving the second side data in duplex printing mode due to the insufficient memory.
Remedy:<User Check> • Print the print data stored in the memory. • The size of printing data per page is too big. Change the printing contents to reduce the data size. • Switch to single-side printing.
1 Main PCB failure Replace the main PCB ASSY.

Lỗi 8903 máy in Brother HL2321

Error Code 8903 Brother HL2321

Display:2-sided Disabled Close the Back Cover of the machine.
Description:The back cover sensor detected that the cover was open in duplex printing mode. (Before registering printing data to engine)
Remedy:<User Check> • Close the back cover correctly.
1 Back cover/duplex tray empty sensor attachment failure Reattach the back cover/duplex tray empty sensor. 2 Boss to push the back cover sensor is broken. Replace the back cover. 3 Back cover/duplex tray empty sensor failure Replace the eject sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

chuyen-sua-may-in-hai-duong