Xem giỏ hàng
Số sản phẩm : 0
Trang chủ»Lỗi máy in»Lỗi - service máy in canon

Bảng báo lỗi máy in Canon MF113W

 

 

 

  • Code: 0001
  • Description:Pickup delay jam
  • Causes:Top Sensor PS3
  • Remedy:
  • Code: 0002
  • Description:Pickup Stationary Jam
  • Causes:Top Sensor PS3
  • Remedy:
  • Code: 0003
  • Description:Fixing delivery delay jam
  • Causes:Fixing Output Sensor PS4
  • Code: 0004
  • Description:Fixing delivery stationary jam
  • Causes:Fixing Output Sensor PS4
  • Remedy:
  • Code: 000C
  • Description:Wrapping jam
  • Causes:Fixing Output Sensor PS4
  • Remedy:
  • Code: 000E
  • Description:Internal stationary jam
  • Causes:Top Sensor/Fixing Output Sensor/Fixing Media Width Sensor PS3/ PS4/ PS5
  • Code: 000F
  • Description:Door Open Jam
  • Causes:Top Sensor/Fixing Output Sensor/Fixing Media Width Sensor PS3/ PS4/ PS5
  • Remedy:
  • Code: E000-0000
  • Description:Fixing temperature control startup failure
  • Causes:Temperature of the Fixing Assembly did not reach the specified temperature within the specified period of time.
  • Remedy:1. Check the harness/connector of the Fixing Assembly. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Assembly. 4. Replace the Engine Controller PCB.
  • Code: E001-0000
  • Description:Abnormal high temperature of Fixing Assembly
  • Causes:It was detected that the temperature of the Fixing Assembly was abnormally high.
  • Remedy:1. Check the harness/connector of the Fixing Assembly. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Assembly. 4. Replace the Engine Controller PCB.
  • Code: E003-0000
  • Description:Abnormal low temperature of Fixing Assembly
  • Causes:It was detected that the temperature of the Fixing Assembly was abnormally low.
  • Remedy:1. Check the harness/connector of the Fixing Assembly. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Assembly. 4. Replace the Engine Controller PCB.
  • Code: E004-0000
  • Description:Fixing Heater drive circuit error
  • Causes:A frequency failure was detected in the Fixing Assembly.
  • Remedy:1. Check the harness/connector of the Fixing Assembly. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Assembly. 4. Replace the Engine Controller PCB.
  • Code: E015-0001
  • Description:Developing Disengagement Motor error
  • Causes:A developing disengagement error was detected.
  • Remedy:1. Check the harness/connector between the Developing Disengagement Solenoid and the Engine Controller PCB. 2. Replace the Developing Disengagement Solenoid. 3. Replace the Motor PCB. 4. Replace the Engine Controller PCB.
  • Code: E066-0000
  • Description:Environment Sensor error
  • Causes:An error in the Environment Sensor was detected.
  • Remedy:1. Check the harness/connector between the Environment Sensor PCB and the Engine Controller PCB. 2. Replace the Environment Sensor PCB. 3. Replace the Engine Controller PCB.
  • Code: E100-0001
  • Description:BD error
  • Causes:BD error was detected.
  • Remedy:1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB. 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB.
  • Code: E110-0000
  • Description:Error in startup of the Scanner Motor
  • Causes:An error in any of the Scanner Motor, Laser Unit, or BD detection was detected at startup of the Scanner Motor.
  • Remedy:1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB. 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB.
  • Code: E110-0001
  • Description:Scanner Motor rotation error
  • Causes:An error in any of the Scanner motor, Laser Unit, or BD detection was detected during steady rotation of the Scanner Motor.
  • Remedy:1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB. 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB.
  • Code: E196-0001
  • Description:Error in accessing the NVRAM
  • Causes:NVRAM cannot be accessed.
  • Remedy:Replace the Engine Controller PCB.
  • Code: E196-2000
  • Description:Controller communication error
  • Causes:The Flash ROM in the Main Controller cannot be accessed.
  • Remedy:1. Update the set of the controller firmware. 2. Replace the Main Controller PCB.
  • Code: E202-0002
  • Description:Reader Scanner Unit HP error
  • Causes:The Reader Scanner Unit could not detect the home position when completing scanning operation.
  • Remedy:1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit.
  • Code: E225-0001
  • Description:Light intensity error
  • Causes:The light intensity of the Scanner Unit during shading is under the specified level.
  • Remedy:1. Disconnect and then connect the Flat Cable. 2. Replace the Flat Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB.
  • Code: E301-0001
  • Description:Light intensity insufficient.
  • Causes:Light intensity at shading was insufficient.
  • Remedy:1. Disconnect and then connect the Flat Cable. 2. Replace the Flat Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB.
  • Code: E733-0000
  • Description:Controller communication error
  • Causes:Communication error between the Main Controller PCB and the Engine Controller PCB
  • Remedy:1. Update the set of the controller firmware. 2. Replace the Main Controller PCB. 3. Replace the Engine Controller PCB.
  • Code: E744-0002
  • Description:Language file error
  • Causes:The size of the language file exceeded the upper limit.
  • Remedy:Update the set of the controller firmware.
  • Code: E744-4000
  • Description:Engine ID error
  • Causes:Invalid engine connection was detected.
  • Remedy:1. Check the D-CON. 2. Update the D-CON. 3. Update the set of the controller firmware. 4. Check the model code (because this error occurs even when the model code and the engine code are mismatched).
  • Code: E744-6000
  • Description:Wireless LAN communication error
  • Causes:Communication error between the Main Controller PCB and the Wireless LAN PCB
  • Remedy:1. Check the connection of the wireless LAN slot (SD-IO). 2. Update the set of the controller firmware. 3. Replace the Main Controller PCB.
  • Code: E760-0001
  • Description:Main Controller PCB error
  • Causes:An error occurred with the firmware of the Main Controller.
  • Remedy:1. Update the set of the controller firmware. 2. Replace the Main Controller PCB.
  • Code: E808-0000
  • Description:Low voltage power supply failure
  • Causes:Low voltage power supply failure was detected.
  • Remedy:1. Check the harness/connector of the Low Voltage Power Supply PCB. 2. Replace the Low Voltage Power Supply PCB. 3. Replace the Engine Controller PCB.


Bài viết nổi bật
Xem toàn bộ

Sản phẩm tiêu biểu

2 3 4 5 6 » ( 74 )
Xem toàn bộ
Tìm Sản Phẩm
Đăng ký thành viên
Xin chào quý khách
Đăng ký | Đăng nhập

Email / Điện thoại

Mật khẩu

Nhớ mật khẩu | Quên mật khẩu

Máy khoan pin Hải Dương
Nhận tin mới
Bạn biết đến dịch vụ chúng tôi thông qua
Bạn bè
Tìm kiếm trên internet
Quen biết
Khác

Thống kê truy cập
Đang truy cập: 33
Trong ngày: 547
Trong tuần: 1283
Lượt truy cập: 2502651
  hp1010máy in hải dương máy in sửa máy in đổ mực inmáy in cũ máy in Hải Dương máy in đảo mặt máy in cũ máy in canon3300 máy in canon6300 máy in hp401d Hải Dươnghp2055d máy inhp2055d máy in hải dương bán máy in hộp mực 2055d đổ mực 2055d đổ mực in hải dươngmáy in canon canon 6300dn máy in 6300dn máy in cũ hải dương máy in canon hộp mực 6300dnmáy in cũ canon canon3018 máy in hải dương máy in cũ máy in canon3108trục từ trục từ canon trục từ hp trục từ máy inbochiamayinbộ chia 4 cổng bộ chia máy in 4 cổng bộ chia máy inmáy in hpm135w hpm135w Hải Dương máy in đa năng sửa chữaneverstop hp mucinhp1000w mucdoneverstopđiều khển máy chiếu điều khiển đa năng máy chiếu khien da nang dieu khien may chieu hai duongmực đổ hp1000w mực đổ hp neverstop mực đổ hải dương đổ mực hpcanon6670 mayincanon máy in canon hải dương đổ mực canonreset samsung reset máy in reset máy in samsung. samsungcanon đa năng canon D520 Hp1212nfxerox p225 máy in cũ p225 xerox p225Canon 6200d máy in canon máy in cũ canon 6200d tại Hải Dươngmực đổ hp107 mực hp hải dươngmáy in hp403dw máy in hải dương hp403dw hp m403dwHộp mực máy 3300 hộp mực hải dương canon 3300 hải dươngHộp mực canon 6200 canon 6200 hộp mực incanon 6200máy in canon máy in canon 3310chíp mực hpm348 chíp mực hpm436 chip hpm436 hpm438chip drum hp436 chíp trống hp436 chip drum hp438máy in cũ hải dương máy a3 hải dương hp706kitreset kithafrimwa ha version hpmáy in mayin in bill máy in wificard in canon 2900 canon 2900 card wifi 2900canon2900 canon2900w 2900w mayincanon 2900sửa máy inmáy in tại Hải Dươngsửa máy in 2900đổ mực in 2900Hải Dươngđổ mực in Hải Dươnglỗi máy in hpm436hp m436error C3-14141máy in hphải dươnglỗi c3-14141 hp436

rivew-maps

TRUNG TÂM DỊCH VỤ KỸ THUẬT BẢO TÍN ĐC: Số 240 Nguyễn Văn Linh - Tp. Hải Dương. Mobile: 0983 593 218 (zalo/facebook)
x
Powered by suamayinhaiduong.net
1
Bạn cần hỗ trợ?